Opens to 7/8"

Made of delrin to prevent from scratching implant surfaces. Wider sizes also useful in revision knee surgery.

Product No’s:
1271 [Package of 10]
Pin Diameter: 3.2mm (1/8")

Overall Length: 70mm
Tip-to-Shoulder Length: 40mm
Blunt-End-to-Shoulder Length: 22mm

Download Product Brochure (PDF)

Product No: 1589
Overall Length: 12.25"
Length to Hinge: 9"
Leg Depth: 2.75"
Prong Dimensions: 12mm L x 4mm W x 3mm D
Opens to 7" Space between Legs

Designed for use with a standard 1.6mm (.062") threaded K-wire (not included).

Allows use of trephine at oblique angles to bone surface by using an anchoring K-wire and cannulated trephine

Avoids “skipping” of trephine teeth on bone surface

Facilitates optimal approach angle and direction of trephine

Variety of core diameters yields bone samples of sufficient size for pathology

Adapters allow for use of a power drill

Minimally invasive — soft tissue sleeve protects surrounding structures and tissue

Can also be used for bone graft harvesting

Repositioning guide allows easy adjustment of targeting K-wire

Product No: 1425-00
Trephine Internal Diameters: 5mm, 6.5mm, 8mm

Removes pins & screws up to 5mm (.2") diameter and wires as small as .8mm (1/32") diameter

Five interchangeable collets for various grasping capacities

Two cross-handle insert rods give strong leverage for locking the collet securely onto the pin

Slap hammer included

Product No: 1215-00
Set includes:
(1) handle draw bar,
(1) closing sleeve with hand wheel,
(5) collets (1mm to 5mm),
(2) cross-handle insert rods,
(1) slap hammer,
(1) sterilization case

Product No’s:

Digit Aligner – 12 Hole

Digit Aligner – 8 Hole

Allows the surgeon to pin these fractures without having to manually hold the fracture reduced, allowing the surgeon to focus on accurate pin placement and reduction. The height of the crossbar is fully adustable to accommodate different size patients. Reduction is acheved by an assistant gently applying axial traction through the forearm, with the crossbar applying the counter traction. Pinning is done with the C-arm in the lateral position. An optional separate attachment to support the arm for distal humerus fractures in adults is available. Unit not sterilizable.

Dorr Femoral Neck Elevators
Placed under the proximal femur to help expose the femoral head. The wide version is useful with large patients, while the narrow is useful when broaching or when the implant is in place.

D6111 [Dorr Wide Femoral Neck Elevator]
Overall Length: 15"
Depth from Handle: 2"
Blade Width at Widest: 45mm

D6113 [Dorr Narrow Femoral Neck Elevator]
Overall Length: 13.75"
Depth from Handle: 2.25"
Blade Width: 25mm

• Simple design for fast and easy positioning

• Multiple elbows allow a wide range of positioning

• Arm connector is mobile and can be easily released for repositioning

• Connects over the drape in the sterile field using the supplied rail clamp

• Compact for easy storage

• Complete unit is autoclavable

Allows surgeons to utilize a forceps or pickup type instrument using a more mechanically and ergonomically favorable grip. Forceps can be used with a full-hand grip or “palmed.”

Product No: 1174
Overall Length: 6.875"

Design helps avoid harming the vascular tissue.

Both compartments are simultaneously but independently tensioned by the same device. Allows for determination of femoral rotation. Can be used with the patella reduced, so that any lateral tightness caused by the everted patella is eliminated. Release can be performed with the device in situ.

Product No: 1212-00
Includes Sterilization Case

Jack Paddles: 60mm x 50mm
Jack Rise: From 12mm to 24mm
Jig: 60mm x 50mm
Chuck Overall Length: 6.875"
Chuck Handle Length: 3.875"
Chuck Hex Length: 7mm

The calibrated handle of the spreader helps to accurately gauge the gap, and makes it possible for two spreaders to be used to assist in balancing ligaments.

Designed to drill cancellous bone in the subchondral weight bearing region of the tibia. This helps to improve the mechanical interlock in the cancellous bone/cement interface.

Product No: 1112
Drill Diameter: 2.7mm

Drill Length: 3mm
Overall Length: 4.75"

Product No: 1833

Overall Length: 7"
Jaw Length: 2.25"
Jaw Width Tapered from: 8mm to 1.5mm
Jaw Heigth Tapered from: 12mm to 2.5mm

When used for partial avulsion, instrument may be inserted beneath the nail plate prior to cutting with a Beaver blade. The lower jaw of the clamp protects the nail bed from laceration as the blade is advanced.

Also helps to prevent from scratching component surfaces.

Hole pattern and two lugs on the bottom of the footpiece yoke allow for quick positioning of the knee in flexion, extension and rotation. Mid-footpice lug can be used in the yoke for holding the leg in extension during cementing or closing. The unit can be sterilized by either gas or steam sterilization. Supplied with sterilizable table clamp which can be clamped over the sterile drape to the O.R. table side bar.

Product No’s:
2610
Base Dimensions: 27" x 10.5"

Optional/Replacement Part:
2629-L [Sterile Pad & Wrap]
2595 [Table Clamp]

The ends of the guide are smooth and can be passed through skin and tissue with less danger to neurovascular structures. Narrow guides are ideal for wrist surgery such as distal radius fractures, intercarpal fusions, carpal dislocations, etc., where K-wires must be inserted from angles not accessible through the initial incision. The guides can be inserted through appropriately placed small peripheral incisions and placed on the bone with direct vision from the primary incision. The K wire is then passed through the guide, helping to protect adjacent soft tissue structures.

Product No’s:
3015-052
Accepts k-wires up to: .052" (1.25mm)
Tube Length: 1.875"
Overall Length: 4.25"
Handle Length: 3.15"

Can be used as a holding device, or as a guide if the surgeon uses the tendon insertion to the patella as level for resection.

Product No: 1164
Overall Length: 10"

Helps to distract the joint and hold the bone, allowing easier access to the base. Can also be used for digital fusions to hold bones better for drilling and cutting applications.

Product No: 1163
Overall Length: 6"

Product No: 3420-09
Overall Length: 14"
Handle Length: 10"
Blade Width at Widest: 48mm
Blade Width at Prongs: 24mm

Before surgery with the patient in the supine position, the arms of the unit are adjusted laterally along the bar to conform to the patient’s ASIS’s. Vertical adjustment is also possible to accommodate various hip positioner designs. After the patient is secured using a hip positioner, the unit is placed on the patient's ASIS's again. The levels on top are referenced to check pelvic alignment, and the operating table can then be rotated until the pelvis is level, yielding a known reference for standard external implantation systems.

Product No: 4025
Overall Length: 18.25"
Arm Length from Bar: 6"

Designed to simplify several small joint procedures:

Pins should be cut short above the pin guides to allow full access to the operative site.

Product No:5074

Overall Length: 6.5"
Metric End: 4mm to 13mm
SAE End: 5/32" to 1/2"

New Torx Bits!